Hello all,
Just thought I'd share a little bit of kit I put together. I've been thinking about drinking coffee when out and about and am sure most of us like a nice espresso/fresh coffee over the freeze dried stuff first thing in the morning.
I have seen some portable coffee makers/presses or drip feeders but they all seemed a mix of bulky, fragile and expensive.
So I did a bit of searching on ebay and have come up with the following.
The main elements I was looking for was cheap, study and small.
Vietnamese coffee cup filter Large size for £2.29
https://www.ebay.co.uk/itm/Vietnam-...var=431782770730&_trksid=p2060353.m2749.l2649
Metal Mesh Filter for £1.05
https://www.ebay.co.uk/itm/60mm-Mes...e=STRK:MEBIDX:IT&_trksid=p2060353.m2749.l2649
Holes on the bottom of the Vietnamese coffee cup are way too large for fine ground coffee so I introduced the metal filter.
After extensive minutes of tests I found that it is best to place the metal mesh filter in the Vietnamese cup, coffee on top and the larger filter with handle that come with the cup on top to act as a sort of weight.
You initially need to pour in the water slowly at first and it will take a few moments before coffee starts dripping through and it can speed up a little afterwards. (maybe a filter that had a slightly larger mesh can be used - but then I am getting into a whole different science there). The coffee cup comes with a lid, so that is handy to use as intended while you wait for the water to drain through to add more so not get any flying bugs in there.
The mesh filter I got was ever so slightly wider than the bottom of the cup. A snug fit but a little filing of the edges would be good to consider.
I had to fill the Vietnamese cup 3 times for standard size coffee mug and very nicely the whole contraption fits very well on it's side in my Mk1 crusader mug. Once thing to note is that the cup is not big enough to sit in the middle of the crusader so you have to position it on the left or right edge but it is perfectly stable and secure siting on 3/4 of its edges.
The only negatives I have found (and which I consider very small) is that as it's an all metal affair it will rattle in your crusader during transport but easily rectified with a wash cloth etc as stuffing. The metal mesh can be a tricky to remove but as said before, light filling the edges will resolve that.
Hope I've bought easier posh coffee to the masses
Cheers
Just thought I'd share a little bit of kit I put together. I've been thinking about drinking coffee when out and about and am sure most of us like a nice espresso/fresh coffee over the freeze dried stuff first thing in the morning.
I have seen some portable coffee makers/presses or drip feeders but they all seemed a mix of bulky, fragile and expensive.
So I did a bit of searching on ebay and have come up with the following.
The main elements I was looking for was cheap, study and small.
Vietnamese coffee cup filter Large size for £2.29
https://www.ebay.co.uk/itm/Vietnam-...var=431782770730&_trksid=p2060353.m2749.l2649
Metal Mesh Filter for £1.05
https://www.ebay.co.uk/itm/60mm-Mes...e=STRK:MEBIDX:IT&_trksid=p2060353.m2749.l2649
Holes on the bottom of the Vietnamese coffee cup are way too large for fine ground coffee so I introduced the metal filter.
After extensive minutes of tests I found that it is best to place the metal mesh filter in the Vietnamese cup, coffee on top and the larger filter with handle that come with the cup on top to act as a sort of weight.
You initially need to pour in the water slowly at first and it will take a few moments before coffee starts dripping through and it can speed up a little afterwards. (maybe a filter that had a slightly larger mesh can be used - but then I am getting into a whole different science there). The coffee cup comes with a lid, so that is handy to use as intended while you wait for the water to drain through to add more so not get any flying bugs in there.
The mesh filter I got was ever so slightly wider than the bottom of the cup. A snug fit but a little filing of the edges would be good to consider.
I had to fill the Vietnamese cup 3 times for standard size coffee mug and very nicely the whole contraption fits very well on it's side in my Mk1 crusader mug. Once thing to note is that the cup is not big enough to sit in the middle of the crusader so you have to position it on the left or right edge but it is perfectly stable and secure siting on 3/4 of its edges.
The only negatives I have found (and which I consider very small) is that as it's an all metal affair it will rattle in your crusader during transport but easily rectified with a wash cloth etc as stuffing. The metal mesh can be a tricky to remove but as said before, light filling the edges will resolve that.
Hope I've bought easier posh coffee to the masses
Cheers