Rainwater harvesting system
- Thread starter British Red
- Start date
Hmmmmm. I have a couple of cheap 25 L water containers with screw assembled taps at the bottom and they seem watertight for a week or so’s camp and travel in the back of the car. The head is about 600mm above the tap.
What sort of leak are we talking about - what sort of head is involved in the system?
In other water applications I have cut soft washers from a silicon sheet.
What sort of leak are we talking about - what sort of head is involved in the system?
In other water applications I have cut soft washers from a silicon sheet.
Itcs the nature of the blanking plates I think. They aren't intended to be drilled. It's a hard, brittle plastic. Drilling them and putting threaded plumbing fittings through them doesn't, consistently, result in a water tight seal despite ptfe, gaskets, silicone etc. A moulded unit is just a better proposition. You can easily make it hozelock, plumbing fitting etc
IBC S60x6 (2 inch) Female to 12.5mm Hozelock Hose Adaptor
IBC S60x6 (2 inch) Female to 12.5mm Hozelock Hose Adaptor - Direct Water Tanks
www.kingfisherdirect.co.uk
£30 for the molded Barb not £25 - I forgot the vat!Itcs the nature of the blanking plates I think. They aren't intended to be drilled. It's a hard, brittle plastic. Drilling them and putting threaded plumbing fittings through them doesn't, consistently, result in a water tight seal despite ptfe, gaskets, silicone etc. A moulded unit is just a better proposition. You can easily make it hozelock, plumbing fitting etc
IBC S60x6 (2 inch) Female to 12.5mm Hozelock Hose Adaptor
IBC S60x6 (2 inch) Female to 12.5mm Hozelock Hose Adaptor - Direct Water Tanks
IBC S60x6 (2 inch) Female to 1/2 inch Hose Barb
These adapters will fit most standard UK and European IBC containers where the outer thread after the valve is a S60x6 male thread. An S60x6 thread measures 60mm
www.kingfisherdirect.co.uk
Still tempting for me as if I’ve got to buy decent hozelock connectors and have faith (the bigger factor) then it’s possibly not too far off being different.
I’m a way off getting them all lined up yet anyway so time to ponder.
I may just do a syphon across the top.
Do you know anyone with a 3D printer?
Someone has designed a programme for just about everything you can think of.
Right now I have orders with my son for hi-viz tent peg tops, hi-viz cam cleats and hi-viz valve caps for the car. (I bought a reel of hi-viz filament.)
Make yourself a coffee and browse:
Thingiverse
or
3D warehouse.
Someone has designed a programme for just about everything you can think of.
Right now I have orders with my son for hi-viz tent peg tops, hi-viz cam cleats and hi-viz valve caps for the car. (I bought a reel of hi-viz filament.)
Make yourself a coffee and browse:
Thingiverse
or
3D warehouse.
If you top join it's harder to pump continuously but safer for leaks£30 for the molded Barb not £25 - I forgot the vat!
IBC S60x6 (2 inch) Female to 1/2 inch Hose Barb
These adapters will fit most standard UK and European IBC containers where the outer thread after the valve is a S60x6 male thread. An S60x6 thread measures 60mm
Still tempting for me as if I’ve got to buy decent hozelock connectors and have faith (the bigger factor) then it’s possibly not too far off being different.
I’m a way off getting them all lined up yet anyway so time to ponder.
I may just do a syphon across the top.
Here!
IBC CAP and BRASS LEVER TAP 1/2" to Garden Hose Connector
This is an IBC adapter with a plated brass lever tap and Snap-On hose connector. Allows the attachment of a standard 1/2" (13 mm) garden hose inwww.ibcadapters.co.uk
So has someone purchased one of these and they did/didn't turn out to be any good ???
I can’t remember what I bought!
I got something but haven’t set everything out yet as there’s a number of stages to sort before I do - got to do it right not rushed!
It’s been a bit of a summer being all over the place (four different locations for holidaying) and having returned home earlier, I’m looking forward to some normality for a while!!
I got something but haven’t set everything out yet as there’s a number of stages to sort before I do - got to do it right not rushed!
It’s been a bit of a summer being all over the place (four different locations for holidaying) and having returned home earlier, I’m looking forward to some normality for a while!!
Ok, I have an IBC and I'd like to have an easy way to dispense water - hose connector, tap , pez dispenser with a funny head. Regan probably.
Just use a rain water barrel tap? I used some when I made our IBC hot tub. The IBC tank is easily drilled out with a forstener bit and the tap goes on finger tight, 5 mins and you’re done. Although it doesn’t have a funny head on it!
