1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

More Man Cave improvements

Discussion in 'Dave Budd' started by Dave Budd, Jul 22, 2014.

  1. abominable_scouse_monster

    Joined:
    Jul 12, 2012
    Messages:
    1,309
    Likes Received:
    0
    Location:
    Liverpool
    Sweet, nice little get out clause there then.
     
  2. Dave Budd

    Dave Budd Gold Trader
    Staff Member

    Joined:
    Jan 8, 2006
    Messages:
    2,716
    Likes Received:
    132
    Location:
    Dartmoor (Devon)
    Managed to get a couple of days in the shed after the Moot and Gathering, so I now have a floor! 22mm flooring chipboard on tanalised timbers, all above a thick damp poof membrane. The walls are clad in 6mm ply (except the corner, where i found I was one sheet short! :censored: ). This weekend, the doors!
    ext14.jpg ext15.jpg
    ext16.jpg

    I wish I'd thought to set a camera up to film the chainsaw coming through the wall :rolleyes:
     
  3. sgtoutback

    sgtoutback Nomad

    Joined:
    Jun 29, 2010
    Messages:
    308
    Likes Received:
    8
    Location:
    Near the fundy
    Awesome looking workshop great extension too. Good luck with it
     
  4. Steve27752

    Steve27752 Settler

    Joined:
    May 7, 2007
    Messages:
    596
    Likes Received:
    2
    Location:
    Berkshire, U.K.
    Still need permission, I am sure it looks good!
     
  5. Dave Budd

    Dave Budd Gold Trader
    Staff Member

    Joined:
    Jan 8, 2006
    Messages:
    2,716
    Likes Received:
    132
    Location:
    Dartmoor (Devon)
  6. Steve27752

    Steve27752 Settler

    Joined:
    May 7, 2007
    Messages:
    596
    Likes Received:
    2
    Location:
    Berkshire, U.K.
  7. Dave Budd

    Dave Budd Gold Trader
    Staff Member

    Joined:
    Jan 8, 2006
    Messages:
    2,716
    Likes Received:
    132
    Location:
    Dartmoor (Devon)
    Here we are again :) Finally looking like a workshop now! The doors are on and bolt from the inside, so the only access is via the main doors as has always been the case (only now I can stand under the porch instead of getting wet when I unlock it!). The lathe and mill are in place, but as yet untested due to me not having wired up the leccy yet. Next up, some more flooring and another bench. Then I can start wiring before I move the bandsaws and wood lathe in from the main room :)

    Getting there, slowly!


    ext17.jpg
    Benches in place, all mounted to the wall and braced.
    ext18.jpg

    I got the lathe onto a runway using the forklift on the tractor. Then pushed/pulled it along until it was at the end, when I realised that it was facing the wrong way and had to turn it 360 on the spot! The trestles are cheapies and rated for 50kg each (well, 100kg per pair). The lathe weighs in excess of 150kg, much care and buttock clenching was needed in the moving.

    ext20.jpg ext21.jpg

    The new toys, in place! :)
    ext22.jpg
     
  8. Mesquite

    Mesquite Anyone for sailing?

    Joined:
    Mar 5, 2008
    Messages:
    22,869
    Likes Received:
    578
    Location:
    ~Hemel Hempstead~
    And where's the one where you went 'Oh bother!!!' :rolleyes::lmao::lmao:

    But joking aside they look like some seriously nice kit Dave goodjob
     
  9. British Red

    British Red M.A.B (Mad About Bushcraft)

    Joined:
    Dec 30, 2005
    Messages:
    25,436
    Likes Received:
    248
    Location:
    Mercia
    Very impressive work - a proper man cave. Count me as "impressed" :)
     
  10. Dave Budd

    Dave Budd Gold Trader
    Staff Member

    Joined:
    Jan 8, 2006
    Messages:
    2,716
    Likes Received:
    132
    Location:
    Dartmoor (Devon)
    Thanks Steve. :buttkick:


    There was a slight hiccup at the start of my heavy lifting and moving. I didn't notice how much tilt was on the back of my tractor and managed to knock the mill off the top of the pallet. Fortunately, the Chinese manufacturers had packed it for a choppy sea voyage and the 1/2" thick plywood box that the mill was bolted to managed to protect it :)

    balls.jpg
     
  11. Mesquite

    Mesquite Anyone for sailing?

    Joined:
    Mar 5, 2008
    Messages:
    22,869
    Likes Received:
    578
    Location:
    ~Hemel Hempstead~
    My pleasure Dave :evilangel:

    At least you get the sympathy vote for such a heart stopping moment :)

     
  12. Dave Budd

    Dave Budd Gold Trader
    Staff Member

    Joined:
    Jan 8, 2006
    Messages:
    2,716
    Likes Received:
    132
    Location:
    Dartmoor (Devon)
    no picture until next week, but I'm pleased to say that I now have power in the new room :) I wired in a ring main today and tested all of the machines to check they work. So far so good! Next up, to rig up the air lines from the compressor and to insulate the new half of the gen shed (sound insulation, not warmth!)
     
  13. Dave Budd

    Dave Budd Gold Trader
    Staff Member

    Joined:
    Jan 8, 2006
    Messages:
    2,716
    Likes Received:
    132
    Location:
    Dartmoor (Devon)
    At last, it is finished! :dancer::dancer::dancer:


    ext24.jpg ext25.jpg ext26.jpg

    This extension has consumed approximately 2 tonnes of timber, 350kg roofing steel/fibreglass, 6kg of nails, 600 screws, 35 oak logs (14-26" in length, 8-14" in diameter) have been sunk and rammed home, 40m electrical wire and a great deal of swearing. All of the new building work this year has cost somewhere short of £2k (not including the machines of course). The only power tools used were the chainsaw to cut the oak logs and a cordless drill/driver, everything else was my very own muscle power; oh and I did the WHOLE thing on my own! The whole building now measures about 25mx8.5m! :Wow: I now have my main forge and grinding room, heat treating room, leatherworking and jewellery room, sandblasting and airtools room, machine room, covered steel storage and a honking great porch!

    A small tour of the new bits then :)

    My bandsaws, positioned so that when cutting long stuff they have a door to poke through on either side of the room ;) The cupboard has some hand tools (planes, drills, etc) that have been rusting in the other room fo years. It also contains some axes.
    bandsaws.jpg axes.JPG

    Most of my steel comes in 3m-6m lengths, so is on racking out the back. Other bits such as O1, 52100 and more special steels are in small pieces and are kept indoors and dry.
    barstock.jpg

    My wood lathe, that has always suffered from the damp noxious air, is now in a dry home.
    woodlathe.jpg

    Shiny new toys! :D Mill and metal lathe.
    mill and lathe.jpg

    Sheet metal working area, still a work in progress. My welder and plasma cutter live here now, as do various sheet metal tools such as hand shears, jenny swage and my amusingy named "mighty mini bender". I'll be putting doors on the front of this too. The white board is to have hand tools pinned to it as well as measuring tools.
    sheet metal.jpg

    Into the next room, my sand blasting cabinet might actually get some use now that it isn't buried in junk!
    sandblasting room.jpg

    and another room, the Power House. In here I have my noisy dirty and voodoo generators. So my battery bank from the photovoltaic setup, diesel generator, large petrol driven compressor and small electric compressor.
    powerhouse.jpg

    and finally the front porch. Here I plan to have a bench, my large hand shear and maybe a small kitchen area. Until they all get sorted, it is housing the extra and left over timber. Also, the packing crate from my lathe has been rebuilt and is full of kindling fo lighting the forge and my kelly kettle


    For anybody thinking about building their own workshop from scratch like this. It does cost less than buying off the shelf, it is possible with limited experience and tools, you can build whatever you really want. But the best piece of advice I would give: Just get somebody else to do it for you! I just wanna make stuff and not build things! :banghead::banghead::banghead: :goodnight:
     
  14. Clouston98

    Clouston98 Woodsman & Beekeeper

    Joined:
    Aug 19, 2013
    Messages:
    4,364
    Likes Received:
    0
    Location:
    Cumbria
    That's the mutts nuts Dave! Nicely done! :)
     
  15. sgtoutback

    sgtoutback Nomad

    Joined:
    Jun 29, 2010
    Messages:
    308
    Likes Received:
    8
    Location:
    Near the fundy
    Very nice. awsome project.
     

Share This Page