Search results

Tanto slip joint. The materials used for this one are 3.2mm RWL-34 steel for the bolsters, blade and back spring, stainless liners and red G10. Hope you like it.

The materials for this one are. Orange G10 scales, stainless liners, and 3.2mm Rwl-34 for the blade and back spring. The total length in open position is: 17cm in close position it’s 9.8cm with 6.5cm cutting edge. Thanks for looking NP

It has been long time that I dint post some of my work here, but summer time in the calendar says holydays:) However, here we go with a project I am working on now. The materials for this one are thunderstorm Kevlar scales and carbon fiber for bolsters, stainless liners and RWL 34 for the...

I like to show you my second slip joint The materials for the handle are thunderstorm Kevlar scales and stainless liners. RWL-34 for the blade and back spring. The total length in open position is 18cm and 10.5cm in the close position, with 6.5cm cutting edge. I hope you like it. Thanks for...

It has been a long time that I dint post something in this forum but i will like to show you my first slip joint folder. The materials are for the handle Carbon fiber and stainless liners. RWL-34 for the blade and back spring. The total length in open position is 18cm and 8.5cm in the close...

And here it's the second friction folder with carbon fiber scales. The only thing left to do now it's to make it sharp and make a sheath for it. I hope you like it. NP

Hi Guys I'm after for a small piece of Orange G10 the dimensions I'm looking for are 8 cm long 4mm thick and 3 cm wide. if you got some you can send me a PM. Mods if this is not the right place please fil free to move it. Thanks NP

I like to show you one of my latest commission. The materials for this knife are. 5mm RWL-34 for the blade, for the scales some nice Box Elder Burl and Corby bolts. The total length it’s 24cm with a 12cm cutting edge. Thanks for looking NP

I will like to show you something i’m working with at the moment, i will make a batch of 4 friction folders of this model but for the moment i will make those 2 ready and after that the next two. The materials for this two are Black G10 for the 1 and carbon fiber for the other one, and stainless...

Few days ago I have start to clean the shop and I have found one of my very first neck knife model totally forgotten together with some other blades I had in a box well I thought I will try something new and her you can see the results of it. The materials are 3.5mm AEBL stainless steel, orange...

Camp - Utility knife Here it's another camp - utility knife i'm working with at the moment the total length is 24cm end the cutting edge it's 11.5cm in 3.5mm RWL-34 steel. Any comments or criticism are welcome. Thanks for looking Nektarios

I like to show you a new camp knife i'm working with at the moment, Blade in 4mm RWL-34 steel total length is 25cm and the cutting edge is 12cm Handle: Box elder burl pivot screws, but i don't know if i will levee the pivots or put some Corby bolts instead. Hope you like it so far. NP

I will like too sow you some of my latest work. still have to take some scratches away from the handles make the sheaths and give them the final polish. number 1 Knife Blade: in 4mm RWL-34 steel. Total length 155mm, and 33mm at the widest point. Handle: Box elder burl, Corby bolts. sheath in...

I will like to show you my new liner lock EDC model. The materials for this liner lock folder are 2mm titanium for the scales, stainless bolsters, G10 carbon fiber and RWL34 for the blade, the total length is 16.5cm and 6.2 cutting edge. Still have to clean it and sharpen it. Hope you like it...

I will like to show you one more friction folder i have made for member of this forum. Materials for this folder are RWL for the blade and back spacer, stainless liners and carbon fiber for the scales and a bit of file work on the spacer and blade. Thanks for looking Nektarios

I will like to show you one of my latest commission for a BB forum member. I hope you like it like i do. Thanks for looking. Nektarios

Well i will like to show you something new I'm working with at the moment , now this is my first try to make a titanium frame lock and still needs a lot of work to do. So far i have cut and give shape to the blade and to the ti scales, next is to cut the lock, and put the stop pin in place...

It has been a long time since I have post something! Due to some personal issues I have not been able to make knives for quite a few months. well today i will like to sow you something i have been working with for the last 3 days, i still have to make some minor touches on the the handle and...

I am waiting for some materials to arrive and in the mean wile i thought i will give a try to make my version of a Wharncliffe knife, a started with a piece of firestorm Damascus and came up with this design, for the handle i will use bock oak scales, lanyard tube, Corby bolts and a Mosaic pin...

I will like to show you a knife i completed yesterday for a BB member. Blade: 4mm, RWL-34 Handle: Amboyna burl, brass liners, lanyard tube, Corby bolts and Mosaic pin. Total length: 230mm, and 31mm at the widest point. Blade length: 11cm. Cheers NP